Procurement notices · Find a Tender + Contracts Finder

Notices

Every UK public-sector procurement notice in one board — open opportunities, closed tenders, awards, and pre-market signals. Filter by deadline, value or CPV, and save your search as an alert.

Closing 24h

Open notices

Closing this week

Don’t miss

Open · all

70,824

Live opportunities

Posted · 24h

317

New notices

Posted · 30d

11,337

All notice types

Awarded · 7d

1,411

Market signal

497 noticesopen · sorted by deadline ascending

Page 22 of 25

Time to close

Value

Type

Buyer

Notice

Closing this week4 notices

25 Jun

£510k

Estimated

Tender

FTS · Works

Arbour Housing Limited

2026/2027 PLANNED MAINTENANCE WORKS – WINDOW AND DOOR REPLACEMENTS, ROOF UPGRADES, ELECTRICAL TESTING AND EPC TESTING

Construction work· Published 08 Jun

25 Jun

£100k

Estimated

Tender

Hastoe Housing Association

GB-Thaxted: MW2420 - Little Maypole - Bridge Replacements

Construction work· Published 05 Jun

25 Jun

£90k

Estimated

Below-thresh.

London Borough of Haringey

DPS1 1373 - Winter pollarding 2026

Architecture & engineering· Published 09 Jun

25 Jun

£90k

Estimated

Below-thresh.

London Borough of Haringey

DPS1 1382 - Winter Pollard 2026

Architecture & engineering· Published 09 Jun

Closing in the next 30 days16 notices

25 Jun

£20k

Estimated

Below-thresh.

Community Centre

Community Food Bank/Food Distribution Hub Operations

Food & beverages· Published 02 Jun

Page 22 of 25

Previous Next

Notice peek

TenderFTS · 069809

Radiation Tolerant Sensors

Sellafield Limited

Status

complete

Estimated

—

Published

16 Jun 2026

Key facts

Notice ID: ocds-h6vhtk-069809
Awarded to: Turck Banner Ltd
Source: Find a Tender

Timeline

Published
16 Jun 2026

Description

The Authority has a requirement for sensors that are capable of operating safely and reliably within defined radiation exposed environments associated with nuclear operations. The requirement is driven by: ∙ Nuclear safety and operational assurance ∙ Asset integrity and reliability ∙ The need for predictable performance under radiation exposure The Authority’s need is outcome based and does not specify any particular manufacturer, brand, or proprietary solution. The Authority requires devices that have been independently tested to exceed a Dose of 1 x 106 Gray. The estimated requirement is for 1,224 Sensors with: ∙ 18mm diameter sensor – 18mm threaded barrel, to be supplied with 2 off M18 x 1mm locknuts ∙ Flush fitting ∙ NAMUR two wire Inductive Sensor - DC 2-wire, nom. 8.2 VDC, Output acc. to EN 60947-5-6 (NAMUR) ∙ Nominal Switching Distance 5mm - 10mm ∙ Sensor head length - Not to exceed 65mm ∙ Fitted electrical Lead (Not M12 connector) – Minimum lead length of 2 metres ∙ ATEX category II 1 G, Ex zone 0 ∙ ATEX category II 1 D, Ex zone 20 ∙ SIL2 (Low Demand Mode) acc. to IEC 61508, PL c acc. to ISO 13849-1 with HFT0 ∙ SIL3 (All Demand Mode) acc. to IEC 61508, PL e acc. to ISO 13849-1 with redundant configuration HFT1 ∙ Protection Class IP67 The Authority requires that supplied sensors are to contain Semi-Conductor (SMD/SMT) devices from the same Semi-Conductor Component Manufacture production batch. An Initial Sensor manufacturing batch of a minimum of 11 Sensors is required to allow for Sellafield Limited initiated Third Party Radiation Tolerance Testing. The remaining Semi-Conductor devices (the same Reel) are to be retained awaiting the conclusion of the Third Party Radiation Tolerance Testing. On conclusion of Radiation Tolerance Testing, if Sellafield Limited deem the sensors to be acceptable, the balance of stated Order Total are to be manufactured from the same SMD/SMT component Reel as those sensors manufactured for the purpose of the test (≥11 sensors). If, the first batch (11 off) sensors are not acceptable to Sellafield limited, a further 11 off sensors are to be produced to allow for repeat Radiation Tolerance Testing, the semi-conductor component requirements remain as above. The Sensor Manufacturer is to create a specific product Part Number for the Authority. Sellafield Ltd Quality Grade 04 for sensors produced for testing purposes, Quality Grade 03 for all other supplied sensors.

You might also see

All Sellafield Limited notices →